FUDforum
Fast Uncompromising Discussions. FUDforum will get your users talking.
Home » Imported messages » comp.lang.php » FORMS, validating mail was sent
Show: Today's Messages :: Polls :: Message Navigator
Return to the default flat view Create a new topic Submit Reply
Re: FORMS, validating mail was sent [message #181918 is a reply to message #181868] Sun, 23 June 2013 11:13 Go to previous messageGo to previous message
Thomas 'PointedEars' is currently offline  Thomas 'PointedEars'
Messages: 701
Registered: October 2010
Karma:
Senior Member
Gordon Burditt wrote:

> + Your mail was dropped on the floor for having an invalid
> From: address. Valid From: addresses likely include ONLY
> those with the host name of the server you are sending
> from and a known valid user on that system. Typically
> only a few users like root can send mail with 'fake'
> (off-system) From: addresses. Hint: Do NOT put a
> user-supplied email address in the From: header.

Utter nonsense. By that logic, Web-mail like GMail could not possibly work,
and it would not be possible to have large e-mail providers in the first
place (because the host name of their servers very likely differs from the
domain of the From header field address).

Valid From addresses include all that meet the Address Specification in
RFC 5322, instead. This is a purely *syntactical* determination. It is the
fact that even addresses for which there are no mailboxes at the sending
server can be used in the From header field value, and that afterwards
checking of addresses is unreliable, that allows spammers to thrive.

One must differentiate between the address used as parameter for the MAIL
FROM (SMTP) command (the “Envelope-From”), and the “From” Internet message
header field. The latter can be anything; the former can, in theory, be
anything unless the *sending* MTA enables counter-measures. It is not
possible to change the Envelope-From with simple PHP commands like mail() as
that is determined by the MTA (like sendmail) used by the PHP executable.

The only good part of this answer is the notion that you invite spammers if
you let the end user specify the From header field address without
authentification; so you should not do that, indeed. The /modus operandi/
of spammers and phishers is to harvest or buy e-mail addresses from various
sources and use them also in the “From” header field value to make the
message look to the recipient like a legitimate e-mail (at first). This
kind of network abuse is also supported by “open relays” – MTAs that would
accept and transfer mail for any MAIL FROM to any RCPT TO.

> + The intended recipient has a slow DNS server. If you
> send emails to 100 recipients at a time, it is likely
> that at least a couple of them have slow DNS servers or
> overloaded mail servers. The mail will stay in the queue
> until the message has been delivered to all recipients,
> and that can take days, even if 98 of them were delivered
> in the first minute.

Utter nonsense. DNS is only used to resolve the target host of the message,
specifically to retrieve the host name from the “MX” or “A”/“AAAA” record of
the target domain, and subsequently to resolve the IP address for that host
name from its “A” or “AAAA” record (this double-handshake is intended as a
safety feature of DNS/SMTP: there must be a host *name* for an MX). There
are no DNS servers anywhere that have a respond time of minutes that would
suggest the remote possibility of a delay of days because of DNS issues
(after all, a backup DNS server is strongly recommended, and there are non-
authoritative answers).

When in rare cases e-mails arrive days later, it is usually due greylisting
and a long sender or receiver message queue that needs to be worked through;
not DNS issues at the receiver's (BTST). Also, the mail queue contains a
*copy* of the message for each recipient (not least because in the worst
case each copy must be sent to a different host). Only those copies that
have not been sent are still in the queue, not the single original message
(“the mail”) itself.

“Overloaded mail servers” also are unlikely to be a reason why a message
stays in the sending queue, because receiving MTAs *also* have an *incoming*
message queue which is worked through to put the message into the
corresponding receivers' mailboxes. Overloading is more likely the reason
why the message does not arrive at the recipient's mailbox sooner, but that
has nothing to do with the message transfer between the MTAs, and nothing
with the sending MTA's outgoing message queue.

>> But you cant execute that without root privileges. Which means having
>> that level of access to the machine and writing an su 'ed wrapper in C
>> and calling that instead.
>
> Sometimes you can get a queue count without root privileges. The
> program that comes with the MTA for this is likely already setuid-root,
> and you may be able to configure allowing ordinary users to get a
> queue count.

man sudo


PointedEars
--
Use any version of Microsoft Frontpage to create your site.
(This won't prevent people from viewing your source, but no one
will want to steal it.)
-- from <http://www.vortex-webdesign.com/help/hidesource.htm> (404-comp.)

Report message to a moderator

[Message index]
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: strange one
Next Topic: how to change old ereg?
Goto Forum:
  

-=] Back to Top [=-
[ Syndicate this forum (XML) ] [ RSS ]

Current Time: Mon Nov 25 02:21:51 GMT 2024

Total time taken to generate the page: 0.05769 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.3.
Copyright ©2001-2023 FUDforum Bulletin Board Software